Factory Cheap Hot DSAW Pipes - Api 5l Line Pipes Grade B To X70 Od From 219mm To 3500mm – Spiral

Short Description:

Product Detail

Product Tags

Feedback (2)

Our well-equipped facilities and superb good quality control throughout all stages of manufacturing enables us to guarantee total buyer gratification for Pipe Welding Requirements , Welded Pipe , China Underground Natural Gas Pipe , In case you are intrigued in almost any of our merchandise, remember to will not hesitate to make contact with us and take the initial step to create up a prosperous enterprise romance.

Factory Cheap Hot DSAW Pipes - Api 5l Line Pipes Grade B To X70 Od From 219mm To 3500mm – Spiral Detail:

The Mechanical Properties of the SSAW pipe

steel grade	minimum yield strength Mpa	minimum Tensile strength Mpa	Minimum Elongation %
B	245	415	23
X42	290	415	23
X46	320	435	22
X52	360	460	21
X56	390	490	19
X60	415	520	18
X65	450	535	18
X70	485	570	17

The Chemical composition of the SSAW pipes

steel grade	C	Mn	P	S	V+Nb+Ti
	Max %	Max %	Max %	Max %	Max %
B	0.26	1.2	0.03	0.03	0.15
X42	0.26	1.3	0.03	0.03	0.15
X46	0.26	1.4	0.03	0.03	0.15
X52	0.26	1.4	0.03	0.03	0.15
X56	0.26	1.4	0.03	0.03	0.15
X60	0.26	1.4	0.03	0.03	0.15
X65	0.26	1.45	0.03	0.03	0.15
X70	0.26	1.65	0.03	0.03	0.15

The Geometric tolerance of the SSAW pipes

Geometric tolerances
outside diameter		Wall thickness		straightness		out-of-roundness		mass	Maximum weld bead height
D		T
≤1422mm	＞1422mm	＜15mm	≥15mm	pipe end 1.5m	full length	pipe body	pipe end		T≤13mm	T＞13mm
±0.5% ≤4mm	as agreed	±10%	±1.5mm	3.2mm	0.2% L	0.020D	0.015D	‘+10% -3.5%	3.5mm	4.8mm

Hydrostatic Test

product-description1

The pipe shall withstand the hydrostatic test without leakage through the weld seam or the pipe body
Jointers need not be hydrostatically tested, providedthat the portions of pipe used in marking the jointers were successfully hydrostatically tested prior to the joining operation.

Traceablity:
For PSL 1 pipe, the manufacturer shall establish and follow documented procedures for maintaining:
The heat identity until each related chmical tests is performed and conformance with the specified requirements is shown
The test-unit identity until each related mechanical tests is performed and conformance with the specified requirements is shown
For PSL 2 pipe, the manufacturer shall establish and follow documented procedures for maintaining the heat identity and the test-unit identity for such pipe. Such procedures shall provide means for tracing any length of pipe to the proper test unit and the related chemical test results.

Product detail pictures:

Related Product Guide:

Based on domestic market and expand abroad business is our progress strategy for Factory Cheap Hot DSAW Pipes - Api 5l Line Pipes Grade B To X70 Od From 219mm To 3500mm – Spiral , The product will supply to all over the world, such as: Georgia, Monaco, Zambia, Many goods fully conform to the most rigorous of international guidelines and with our first-rate delivery service you will have them delivered at any time and in any place. And because Kayo deals in the entire spectrum of protective equipment, our customers don't have to waste time shopping around.

Drain Line

Gas Pipe Fitting

Hollow-Section Structural Pipes

Pipe Line Construction

Good quality and fast delivery, it's very nice. Some products have a little bit problem, but the supplier replaced timely, overall, we are satisfied.

By Austin Helman from Algeria - 2017.09.26 12:12

We always believe that the details decides the company's product quality, in this respect, the company conform our requirements and the goods are meet our expectations.

By Mavis from Uruguay - 2017.11.01 17:04

Write your message here and send it to us